Ich will gerade den Rotorkopf FBL für den T-Rex 500 zusammen bauen. Dabei ist eine weisse Unterlegscheibe (HN70505) http://www.rjxhobby.com/en/pro_detail.asp?id=1384 die ich in der Anleitung nicht wieder finde. Wo gehört die scheibe hin?
Danke
Matthias
Aufbau FBL500
- Matthias23
- Beiträge: 407
- Registriert: 17.04.2011 13:17:20
#1 Aufbau FBL500
T-REX 450 Pro: 3x DS410, 1x DS520, Microbeast, YGE40, Scorpion HK2221-8
T-REX 500 ESP: 3x DS510, 1x DS520, RJX, Microbeast, YGE80
T-REX 600 EFL Pro: 3x DS610, 1x DS650, Microbeast, YGE90HV
Blade MCPx & LMH 120
-
- Beiträge: 538
- Registriert: 25.03.2006 15:20:31
- Wohnort: Schwäbisch Gmünd *
#2 Re: Aufbau FBL500
Hallo,
Die ist bestimmt 1mm dick, oder?
Wenn ja, dann ist die zum Ausgleich der 9mm Aufnahme der RJX-Blätter gedacht.
Grüßle
David
Die ist bestimmt 1mm dick, oder?
Wenn ja, dann ist die zum Ausgleich der 9mm Aufnahme der RJX-Blätter gedacht.
Grüßle
David
#3 Re: Aufbau FBL500
Genau, die gehören zwischen Blätter und Blatthalter.
Compass 7HV V-Stabi 5.2 Pro, Scorpion 5025, YGE 160 HV, Hercules Super BEC, MKS HBL 950/980
Protos Hyperion HV-Servos, 3226, VStabi usw.
Futaba T8
"Science is like sex. Sure, it may give some practical results, but that's not why we do it." Richard Feynmann
heliaddict
Protos Hyperion HV-Servos, 3226, VStabi usw.
Futaba T8
"Science is like sex. Sure, it may give some practical results, but that's not why we do it." Richard Feynmann
heliaddict
- Matthias23
- Beiträge: 407
- Registriert: 17.04.2011 13:17:20
#4 Re: Aufbau FBL500
Super, danke.
Jetzt habe ich noch Schrauben 2x 3x24mm und 1x 2.4x20mm sowie passende selbstsichernde Muttern über. Ich vermute die sind zur Befestigung an der Hauptrotorwelle, wobei ich beim T-Rex 500 nur eine brauche?
Jetzt habe ich noch Schrauben 2x 3x24mm und 1x 2.4x20mm sowie passende selbstsichernde Muttern über. Ich vermute die sind zur Befestigung an der Hauptrotorwelle, wobei ich beim T-Rex 500 nur eine brauche?
T-REX 450 Pro: 3x DS410, 1x DS520, Microbeast, YGE40, Scorpion HK2221-8
T-REX 500 ESP: 3x DS510, 1x DS520, RJX, Microbeast, YGE80
T-REX 600 EFL Pro: 3x DS610, 1x DS650, Microbeast, YGE90HV
Blade MCPx & LMH 120
- Matthias23
- Beiträge: 407
- Registriert: 17.04.2011 13:17:20
#5 Re: Aufbau FBL500
Schon gut, beim Demontieren der Blätter vom Originalrotorkopf ist es mir aufgegangen %)
T-REX 450 Pro: 3x DS410, 1x DS520, Microbeast, YGE40, Scorpion HK2221-8
T-REX 500 ESP: 3x DS510, 1x DS520, RJX, Microbeast, YGE80
T-REX 600 EFL Pro: 3x DS610, 1x DS650, Microbeast, YGE90HV
Blade MCPx & LMH 120